Guide to Drawing decorative squares using Corel Draw 12

View: 748    Dowload: 0   Comment: 0   Post by: hanhga   Category: CorelDRAW Graphics   Fields: Other

In this exercise we use the drawing tool rectangle (Rectangle), circle (Ellipse) and some of the following commands:

- Tranfrom - Position: change objects in a precise location on the screen.

- Align and Distribute: to than their subjects.

- Trim: Create third object from two objects intersect.

- Combine (Ctrl + L): link object, the intersection of the objects will be created by the empty area.

- Break Curve Apart (Ctrl + K): Reimbursement an escape groups Combine command.

- Intersect: Creates third object, the intersection of two objects.

- Fill Tool: coloring tools.

- Outline Tool: tool contour.

Colouration:

- Select the rectangle drawing tool (Rectangle), draw a square the size of 10 cm by pressing Ctrl + left mouse click and drag the cross.

- On the Object properties bar in the cell (s) Size 10 cm type, in cells Nonproportional Scaling / Sizing Ratio padlock icon selected (blocking).

- Choose Object - Transformations - Position: Relative Position section in the middle and press the center select Apply To Duplicate card to add a second square is located on the first position of the image.

- Select tool to draw a circle (Ellipse) to draw a circle with a diameter of 10 cm.

- After drawing the circle is complete, select the circle and square.

- Choose Object - Align and Distribute:

Align Centers Horizontally

Align Centers Vertically

- Choose Object - Transformations - Position:

Relative Position: turn the box between the left edge, cell center of the bottom and middle of the right side box

Click Apply To Duplicate card (Figure 3).

- Choose 4 round and 1 square.

- Choose Object - Shaping - Trim (Figure 4).

- Turn to select 4 circle diameter reduced to 9 cm (Figure 5).

- Choose 4 circle.

- Choose Object - Transformations - Position:

Relative Position: in the center box

Click Apply To Duplicate card.

- In turn, select the newly created 4 circle diameter reduced to 7 cm.

- Just pick one big circle and 1 small circle with the same center, press Ctrl + L. I get one donut.

- Similar to the three remaining pairs of circle we added 3 donuts (Figure 6).

- In turn, select each donut and drew the first square.

- Choose Object - Shaping - Intersect: It was assigned 4 objects are part of 4 donuts and 1 square.

- Choose 4 donuts click Delete (Figure 7).

- Choose a square and a few objects like.

- Select tool Outline Tool - Outline Pen Line routing of the objects as you like.

- Select the object and color you like, we get the results shown in Figure 8.

Select the rectangle drawing tool (Rectangle), draw a square the size of 10 cm by pressing Ctrl + left mouse click and drag the cross.

Posted on 29-12-2015

Comment:

To comment you must be logged in members.

Files with category

• Documentation UDK Create print Firefly Particles

Category: CorelDRAW Graphics     Fields: Other

Codetitle be learning some of the basics of UDK’s Particle system while creating a Firefly particle. We'll start by creating a texture for our particle in Photoshop and then move to UDK where we'll learn how to turn that texture into particles,...

• Female Character Modeling Guidelines do print Blender

Category: CorelDRAW Graphics     Fields: Other

In the final part of the Female Character Modeling series, you'll learn how to use existing geometry to create a dress and socks for the character. You'll then complete the project by adding additional details, such as wrinkles and creases using...

• Create a Low Poly Guide Camera print Blender

Category: CorelDRAW Graphics     Fields: Other

Create a Low Poly Guide Camera print Blender.In this tutorial we will learn how to unwrap the car model we created in the first part of this series, and create its texture.

• Modelling & Rigging Guide print a Cartoon Parrot Maya

Category: CorelDRAW Graphics     Fields: Other

In the UV Texture Editor window, you can see the selected feather UVs which was unwrapped in the previous part of the tutorial.With the feather mesh selected in the viewport, go to Polygons > UV Snapshot

• Modelling & Rigging Guide a Cartoon Parrot

Category: CorelDRAW Graphics     Fields: Other

Modelling & Rigging Guide a Cartoon Parrot. With the parrot's body selected, secondary-click on the mesh and go to Assign Favorite Material > Lambert.

• Guide Single-Point Tracking in Blender using Coreldraw Graphics

Category: CorelDRAW Graphics     Fields: Other

Now you can see the footage inside the movie clip editor window. Click on Prefetch Frames button to load the image sequence in the RAM. Alternatively, press the P key.

• How to Create a Fuel Pump using corelDraw Graphics

Category: CorelDRAW Graphics     Fields: Other

Open the fuel pump file in Maya which was saved in the previous part of the tutorial.Go to Window > Settings Performances > Plug-in Manager.

• How to Create a Realistic 3D Sphere Logo from Scratch Using CorelDraw

Category: CorelDRAW Graphics     Fields: Other

In this tutorial you'll learn how to make a realistic 3d sphere logo. This tutorial is for designers who use CorelDraw as their main software. This kind of logo works well for technology focused companies, as it has a high-tech feel. After working...

File suggestion for you
• Javascript - 386 view We all know what Serializable interface guarantees i.e. ability to serialize the classes. This interface recommends you to useserialVersioUID also....

• WordPress template - 737 view Chances are that you want to set some kind of minimum requirements on your WooCommerce store before your customers checkout.

• Flash template, Flash game - 659 view In this Quick Tip you will learn how to use BitmapData's copyPixels() method to create a very fast blurry trail effect for the bullets in your...

• Web Development - 222 view Speech to Text Recognition for Data Scraping and Collection in Data Mining

• Visual studio & .NET - 745 view This is a simple application that will teach you on how to create a screen resolution detection program using visual basic.NET framework. It...

Mega tags
• Sharepoint - 999 view According to Microsoft, "Microsoft® Content Management Server (MCMS)...

• References - 1994 view In the process of web design, which makes it the most headaches is how...

• Javascript - 309 view When I began searching for my first job as a web developer, I applied...

• HTML-CSS template - 1697 view Clipping path is the path we use to clip an element, it marks out our...

• Javascript - 919 view In the course of my website, still regularly meet the requirements for...

• Mobile applications - 151 view This application shows you how to create an E-post office where you...

• Javascript - 311 view In previous tutorial, we learned about four persistent states of...

• HTML-CSS template - 6417 view Prior to HTML5 we had no element to semantically mark up a date or...

• HTML-CSS template - 629 view There are times, however, when a lightweight carousel with minimal...

• HTML-CSS template - 1046 view Share Template HTML&CSS Artificial Casting- By Piyush